Ecomm’s wireless control network and energy management system has been specifically designed to be scalable to many different size buildings, from relatively small commercial facilities to large industrial and residential properties. Ecomm has added control and output capabilities to the wireless range.
- The network features a large possible mesh size: up to 75 full function devices plus 150 reduced function devices.
- Browser-based remote configuration and maintenance for convenient real-time monitoring and remote system control.
- Self-forming network is easy to start up.
- Integrates to open protocol automation systems via Modbus RTU and Modbus TCP.
- Self-healing mesh makes the network outstandingly reliable.
Applications include:
- Housing
- Retail space
- Hospitality
- Assisted living facilities
- Space management
- Transportation facilities
EC1 Gateway
The EC1 is an 802.15.4 PAN Coordinator supporting all ECOMM RF Mesh Full Function Devices (FFD) and Reduced Function Devices (RFD). It hosts all configuration and management tools embedded on the device and presented through a web interface. Each EC1 supports 75 FFD’s and up to 150 RFD’s. Data interface to external systems is by Modbus TCP or other protocols using protocol converter.
WC21 FFD Mesh router repeater with I/O
The WC21 is a Full Function Device with two configurable inputs for thermistor, dry contact or pulse and two Form C relay outputs for up to 30VAC or DC at up to 1 amp. The WC21 also has an RS485 ModBus RTU communication port for support of third party devices that have been characterized to be accepted and operate on the ECOMM Sensor Link Mesh Network.
WC21-813 8 analogue input/13 relay output
The WC21-813 Wireless I/O Module comes as a 2 Piece set consisting of a WC21 FFD Mesh Node and an 8 Input 13 Output ModBus RTU Slave I/O Module along with a 4 Conductor Comm/Power cable 400 mm in length which connects the two devices. Inputs supported, 0-5 VDC, 0-20 ma, Contact Closure and 10 K Ohm Type III Thermistor. Outputs are Form A, 1 Amp 30 VAC/VDC, with Hand/Off/Auto switches for each Output.
WC21-32 32-channel analogue input
The WC21-32 Wireless Input Module comes as a 2 Piece set consisting of a WC21 FFD Mesh Node and a 32 Input ModBus RTU Slave I/O Module along with a 4 Conductor Comm/Power cable 400mm in length which connects the two devices. Inputs supported, 0-5 VDC, 0-20 mA, Contact Closure and 10 K Ohm Type III Thermistor. The I/O module also provides a 24 VDC loop power supply for 0-20 mA sensors.
WC21-1048 10-channel analogue input/ 4 analogue and 8 relay output
The WC21-1048 Wireless I/O Module comes as a 2 Piece set consisting of a WC21 FFD Mesh Node and a 10 Input , 4 Analog Output, 8 Digital Output ModBus RTU Slave I/O Module along with a 4 Conductor Comm/Power cable 40cm long which connects the two devices. Inputs supported, 0-5 VDC, 0-20 ma, Contact Closure and 10 K Ohm Type III Thermistor. Digital Outputs are Form A, 1 Amp 30 VAC/VDC, with Hand/Off/Auto switches for each Output. Analog Outputs are 0-10 VDC and 0-20ma with Hand/Off/Auto switches for each Output.
WC21-16DI 16-channel contact closure or pulse input
The WC21-16DI Wireless digital input module comes as a 2 Piece set consisting of a WC21 FFD Mesh Node and a 16-channel ModBus RTU Slave input module along with a 4 Conductor Comm/Power cable 40cm long which connects the two devices. Inputs supported are Contact Closure and Pulse. The inputs are isolated from the logic by bi-directional opto-couplers. The inputs are divided into 2 isolated groups of 8 inputs each. Each channel can be used as either a contact closure detection or as a 32-bit pulse counter. Both register types for each channel are available simultaneously on the wireless gateway.
WC21-P2 Point to point pulse bridge
The WC21 P2 is a Set of WC21 I/O Modules, that are dedicated Point to Point transmission of Pulse generated contact closures from Meter to BAS or Data Acquisition Input terminus point. The Meter Input Module accepts 1 Pulse Input and the Receiver Module has 2 Outputs, one for the Replicated Pulse and 1 for alarm condition, loss of RF Link and/or Low Battery condition on the Meter Input Module.
WT770 Multi-stage thermostat controller
The WT770 is a conventionally wired 24 Volt, 2 Stage Heat, 2 Stage Cool, 3 Fan Speed Thermostat. It comes equipped with a Full Function Device Mesh Radio in the Sub-Base of the Thermostat. Configurable for Gas/Electric, Heat Pump ( B or O ) orientation of the reversing valve, Fan Furnace Control and 44 configurable parameters in the set-up menu that allow for complete customization of each Thermostat.
WC21-SH1 Battery powered temperature and humidity sensor
The WC21-SH1 is a battery powered, multi-function sensor. It hosts an on board Temperature / RH Sensor, +/- 2% accuracy on RH and +/- 0.5 deg C. The WC21-SH1 also supports a single Remote wired Thermistor. The WC21-SH1 is powered by two AA Batteries.
WC21-P1 Battery powered pulse counter
The WC21 P1 is a Single Input Battery Powered RFD Pulse Counter. When associated with a WC21 FFD there may be up to 5 WC21 P1 RFD’s as Star Nodes. The WC21 P1 operates on two AA batteries with a recommended battery selection of Energizer Ultimate or equivalent which will yield 3 Year battery life transmitting at 60 Second Intervals.
WT22 Battery powered temperature, humidity and PIR sensor w/display
The WT22 is a Battery Powered Reduced Function device which comes standard with Backlit Display, Function Buttons and PIR Motion Sensor as an embedded application component. On board Sensors include Temperature and Humidity, +/- 2% accuracy.
WO12 Battery powered PIR and door contact sensor
The WO12 is a battery powered, multi-function sensor. It hosts a PIR motion sensor, magnetically operated door switch, and has two configurable inputs for either 30 K Ohm Thermistor temperature sensors or contact closure. The WO12 also has an on board Tamper switch as a discrete input. The WO12 operates for 2 Years on two standard alkaline AA batteries, which are purchased separately.
WO12-T Battery or Line powered temperature sensor
The WO12-T is a Battery or Line Powered (24VAC 50/60 ) Reduced Function Device. The RFD can support 1 Wired Thermistor Sensor of any form factor, 30 K Ohm.
WT21 Battery powered temperature and PIR sensor w/display
The WT21 is a Battery Powered Reduced Function device which comes standard with Backlit Display, Function Buttons and PIR Motion Sensor as an embedded application component. On board Sensor is Temperature +/- 0.5C accuracy.For data sheet see WT22.
SlideShare
Twitter
Facebook
YouTube
LinkedIn